888.488.2028

2017-2020 Audi B9 S4/S5/SQ5 3.0T Integrated Engineering Turbocharged Performance Stage 1 ECU & TCU Combo Tune (IESOVZ11)

Your 2017-2020 Audi S4 or S5 is the home to a turbocharged 3.0L V6 powerhouse begging to be let loose. IE's performance calibrations unleash your car's full potential right out of the gate. Maximized for incredible power at home on the drag strip and road course while maintaining full comfort and reliability on your everyday commute. Experience IE's Performance ECU Software yourself with a simple install that takes only minutes from the comfort of your own driveway. EASY POWERFLASH AT HOMEFASTER IN MINUTES HARDWARE & FUELPOWER OPTIONSMULTIPLE STAGES ENDLESS FUNFEATURE PACKEDENJOY THE DRIVE       LEADING FEATURES IE Stage 1 & Stage 2 software brings track-ready ECU programming to your turbocharged 3.0L V6 engine while retaining factory comfort and reliability. IE's own tuning technology suite is used to completely reverse-engineer the factory ECU mapping, allowing our software engineers access to realign all safety protocols and sensors for the new performance calibration. Every tune parameter undergoes months of testing on our in-house dyno systems that utilize the world's only Sea Level Generator developed specifically to verify tune operations in any condition. Confidently drive from LA to Pikes Peak with power that will keep you smiling every mile!   Horsepower & torque gains maximized 91, 93, E40, & E85 fuel maps for Stage 1 & 2 Stage 1 for stock hardware or basic bolt-ons Stage 2 for full bolt-on support Stage 1 & 2 Plus HPFP for massive mid-range power gains Stage 1 Transmission Tune included with ECU purchase Stage 2 Transmission Tune upgrade available  Recalibrated factory boost gauge displays higher boost Neutral/park rev limit raised to 6500 RPM Brake boost enabled for rolling launch Annoying auto-start/stop defaults to off (button turns back on) More aggressive overrun/crackle in Dynamic mode (Stage 2) Crackles enabled for free revving in park or neutral Engine VE is completely remodeled for a smooth power curve Maximized throttle scaling for dependable throttle use Boost control reconfigured for smooth and crisp power delivery Optimized EGT for safe fuel ratios and maximized power output Eliminated/minimized turbocharger surge Reduced turbocharger lag Road speed limiters removed Engineered for all climates and elevations Direct port OBDII at-home flashing Easy octane switching takes only minutes Read and clear diagnostic/problem codes Easy to use Data-logger B9 3.0T STAGE 1 IE Stage 1 ECU calibration dramatically increases performance with up to 505HP & 585TQ, transforming your turbocharged 3.0L into a truly performance-classed vehicle. IE's advanced tuning strategies leave no hidden power on the table and safely max out the factory turbocharger's capability. Engineered to operate on entirely stock hardware and compatible with basic bolt-ons (intake, turbo inlet, intercooler) without the need to retune. See performance tab for full performance results & dyno reports B9 3.0T STAGE 2 IE Stage 2 performance software is a complete engine calibration for full bolt-on stock turbo builds running an aftermarket racing downpipe and catalyst. The unique B9 EA839 engines are equipped with a smaller factory turbo and large stock downpipe with incredibly minimal exhaust restrictions. Using advanced calibration techniques, IE calibrators can extract full peak power on pump gas and ethanol fuels on Stage 1 and 2 downpipe setups. However, the required hardware upgrades for stage 2 will increase airflow, lower intake air temps, faster IAT recovery, and produce an overall more efficient and faster vehicle on the same power. See below for a complete list of Stage 2 hardware requirements STAGE 1 & STAGE 2 PLUS HPFP Stage 1 & 2 Plus ECU tunes are calibrated to support increased fuel delivery from upgraded HPFP (High-Pressure Fuel Pump) internals providing additional horsepower and torque through the mid-range of the power band. Acceleration dramatically improves with a 52HP gain in the mid-RPM (peak HP number remains the same) and up to 75ft-lbs of additional torque on E85! Our matching Stage 2+ TCU transmission tune (sold separately) also includes optimized shift points that double down on the intense pull through the middle of the powerband, further increasing acceleration and faster 1/4 mile times. Stage 1+ & 2+ tunes are included at no additional cost Requires HPFP upgraded internals with 11.7mm pin size     ETHANOL FUELS E85 & E40 blend ethanol fuels are included with all stages and unlock the most performance potential from our ECU tunes. Ethanol contains tons of oxygen, burns cooler, and has a high resistance to knock. This provides more horsepower and torque than running conventional gasoline and is much less expensive than race gas. FULL E85 IE calibrators spent many months developing and testing ethanol blends on the B9 3.0T engines in many climates and elevations. Results were consistent that full E85 runs very close to or beyond the limit of the factory direct injection (DI) fuel system in the mid-range but allows for more power up top. IE's E85 calibration keeps mid-range power in check to avoid lean conditions, misfires, and power loss then ramps it up top for amazingly fast and consistent track times in a drag racing scenario. E85 is also great for easy fill-ups at the pump for daily driving without mixing blends. E40 BLEND E40 is an ethanol mix of E85 with regular pump 91/93 fuel creating a lower ethanol content fuel. E40 offers the optimal ethanol content for the factory DI fuel system in the mid-range of the power band. The lower content ethanol allows this file to create the maximum power output from 3000RPM-4000RPM, perfect for road course and track racing. E40 will also result in a faster feeling car in most street driving situations.  An ethanol content sensor kit is highly recommended when running ethanol blends.     BRAKE BOOST Commonly used in roll racing, Brake Boosting allows you to build extra boost by applying brake pressure while accelerating. Release the brake pressure for a "rolling launch" or extra surge of power.  Brake Boost is included on all tune stages. EXHAUST OVERRUN The stock calibration features a very mild overrun/crackle when you decelerate from higher RPM, but is very hard to hear with factory downpipe/exhaust. Stage 2 files turn up the aggressiveness of this overrun and enable crackles on free-revving in neutral or park. Not only will your car drive faster, it will sound faster too! Guaranteed to put a smile on your face. Exhaust Overrun is included on stage 2 tunes. BOOST CONTROL The stock ECU boost control is delivered in a very “close enough” and erratic boost curve. This slow response is reflected in the factory torque curve and can be felt on long power pulls when utilizing the entire powerband. To smooth out this torque curve, IE calibrators re-tuned the boost control mapping to be much faster achieving precision boost request targeting that results in unmatched power delivery. THROTTLE MAPPING The new generation Audi MG1 ECU uses a complicated mass flow model to calculate boost control. Typical ECU tunes simply raise the wastegate pressure, however, since the maps that control wastegate position (boost) are not controlled by throttle input resulting in limited throttle predictability. To avoid delivering full-boost at half throttle input, IE engineers have taken the care to rescale the entire mass flow model mathematically over 30 maps which correct the entire range of throttle input. This delivers a linear and predictable throttle pedal which improves drivability in every situation on the street or track. EGT OPTIMIZATION Exhaust Gas Temperature (EGT) is the measurement of fuel mixtures exiting the exhaust and is used to determine the health of the fuel/air mixture entering the engine. IE engineers have spent countless hours adjusting boost air/fuel ratio, ignition timing angle, camshaft phasing, intake air temps, and much more to develop the proper EGT adjustments for ultimate engine safety without sacrificing power on all octanes. Since Ethanol burns cooler than gasoline, the extra fuel left over in the cylinders acts as coolant further reducing combustion temperatures and allows for a leaner air to fuel ratio without dangerous EGT levels. All IE files contain safety measures and complete knock control to keep the engine producing its potential within verified and safety-first operation. RECALIBRATED VE The factory engine calibration shows a significant drop in torque and power around 3000 RPM due to the unique volumetric efficiency (VE) of the stock 3.0T engine. Instead of tuning around this drop in VE or attempting to simply raise the factory torque/load maps to compensate, our calibrators have completely solved and removed this drop from our ECU calibrations entirely.  IE's dyno charts are ported directly from our in-house dyno cells and are not modified or "smoothed" in any way. UPGRADING STAGES Upgrading from Stage 1 to Stage 2 or Stage 3 is easy! With IE, you only pay the difference in tune cost with no extra fees. When you install the required matching hardware, simply follow the link on your IE POWERlink software to purchase the tune upgrade and you will be enjoying the next level of power in minutes! HARDWARE GUIDE STAGE 1 COMPATABILITY PART UPGRADE COMPATIBLE REQUIREMENT STAGE 1 TCU TUNE (INCLUDED)   Required STAGE 2 TCU TUNE   Highly recommended AIR INTAKE   Highly recommended TURBO INLET PIPE   Fully compatible with all stages INTERCOOLER   Fully compatible with all stages HPFP UPGRADE   Use with Stage 1+ only CATBACK EXHAUST   Fully compatible with all stages DOWNPIPE X Not Compatible With Stage 1 STAGE 2 COMPATABILITY PART UPGRADE COMPATIBLE REQUIREMENT STAGE 1 TCU TUNE (INCLUDED)   Required STAGE 2 TCU TUNE   Highly recommended DOWNPIPE   Required AIR INTAKE   Highly recommended TURBO INLET PIPE   Highly recommended INTERCOOLER   Required HPFP UPGRADE   Use with Stage 2+ only CATBACK EXHAUST   Fully compatible with all stages DOWNPIPE NOTICE: BY PURCHASING A MOTORSPORT/RACING PRODUCT ("PRODUCT"), YOU REPRESENT THAT YOU UNDERSTAND AND AGREE THAT: THE PRODUCT IS NOT DESIGNED TO MEET ANY APPLICABLE EMISSIONS STANDARDS, WHETHER IN THE USA OR OTHERWISE, THE PRODUCT IS NOT C.A.R.B. COMPLIANT, AND THAT THE PRODUCT IS NOT FOR SALE OR USE IN CALIFORNIA, USA NOR ANY OTHER JURISDICTION WHERE THE SALE OR USE IS PROHIBITED BY LAW. INTEGRATED ENGINEERING, LLC MAKES NO REPRESENTATIONS, WARRANTIES, OR CLAIMS THAT THIS PRODUCT COMPLIES WITH ANY APPLICABLE EMISSIONS LAWS AND EXPRESSLY DISCLAIMS ANY AND ALL SUCH REPRESENTATIONS, WARRANTIES, AND CLAIMS, WHETHER EXPRESS OR IMPLIED. BY PURCHASING THIS PRODUCT, YOU REPRESENT, WARRANT, AND AGREE THAT IT IS YOUR RESPONSIBILITY TO INFORM YOURSELF OF ANY LAWS OR REGULATIONS THAT MAY APPLY TO YOUR PURCHASE AND/OR USE OF THE PRODUCT.  
Your 2017-2020 Audi S4 or S5 is the home to a turbocharged 3.0L V6 powerhouse begging to be let loose. IE's performance calibrations unleash your car's full potential right out of the gate. Maximized for incredible power at home on the drag strip and ...
About IE At Integrated Engineering (IE), we love to build, drive, create and innovate performance driven Volkswagen and Audis. We know first-hand the importance of quality designed, engineered, and reliable parts. That is why our team is dedicated to providing high-quality automotive performance products without compromising quality. We specialize in making your Audi or Volkswagen go faster for longer and stand behind all our products. Our customers have grown to expect a quality build and finish that we strive to over deliver on, not only to manufacture the best, but to ensure the final product performs as well as it was engineered. This begins with an in-depth design process that can take months to years, and through specialized software, the digital product is designed and re-imagined many times over. From here, many products are "rapid prototyped" in ABS plastic to check dimension, fit, and in some cases application. Many of our high-power performance products such as connecting rods, camshafts, and valve train components undergo hours of ruthless testing on our in-house engine and chassis dyno facilities. This ensures that our products have real world-data, for real-world results, on real-world cars. At Integrated Engineering, we believe our commitment to bring you the highest quality performance products available with un-compromised performance truly sets us apart from the rest.  What began as two brothers, Peter & David Blais grew up with a shared passion for racing. That passion grew and Integrated Engineering was founded in 2007 in Salt Lake City, Utah. Since then, IE has set a new standard for performance products in many areas including connecting rods, camshafts, valve train, and billet accessories. Integrated Engineering has made a mark in the enthusiast community and continues to offer the quality and performance orientated product our customers demand. Our passion for the VW & Audi performance industry is clear, whether you interact with us on our website, phone, email, or online.
About IE At Integrated Engineering (IE), we love to build, drive, create and innovate performance driven Volkswagen and Audis. We know first-hand the importance of quality designed, engineered, and reliable parts. That is why our team is dedicated to p...